FOR SALE                                               ( click on the picture to make larger )
GASENGINETOM
Feel free to contact me with any questions about the engines for sale.

Call me at 614-306-0908.

I attend shows and auctions around the country, so delivery is possible.

Shipping is also available, but you must contact me directly.
2 HP Hornsby                $15,500
  • original
  • very nice engine
  • have not found any b/c/w's
  • good compression
  • Original portable outfit
  • early oil engine
  • runs nice ( watch video below)
  • nice bright  work
  • has wineglass oilers
  • 33" x 4" flywheels
  • 4 3/4" bore
  • curve spoke flywheels
  • counter balanced crankshaft
  • big for a 2  HP engine
  • water pump
6 HP Gould, Shapely, & Muir   $9,500
  • older restoration but looks good
  • very nice engine
  • good compression
  • ported exhaust
  • has oilers
  • 35" flywheels
  • 5" bore
  • fuel pump
  • water pump
GEM set $450
I have one set that is almost complete from 1966 thru 2006, missing only
6 issues.

Issues needed:
1975 issues 3, 4, 5
2001 issue 9
2006 issues 1, 9

I have extra issues years 1969 thru 2003, most years I have complete.  
For those let me know your needs for individual prices or complete
years.

I am missing a few for my personal set.

Issues needed:
2010 issue 5
2009 issue 3
2008 issues 1 & 3

If you buy a set I can bring them to Portland or Coolsprings because it
will be several boxes.
I have 90 issues of Farm Collector, years 1999 thru 2012 (with some
missing issues), $125 takes all.
2 HP Sparta       parting out
  • what you see is what I have left
  • engine had compression and would
    probably have ran but one flywheel
    was cracked and could not find
    another
1 3/4 HP IHC Mogul             $1,500
  • older restoration
  • intake valve leaks compression,
    head probably needs removed and
    lap the valve
  • fuel pump
  • nice show piece
  • I have found no breaks, cracks, or
    welds
  • on original skids
  • brass mag
  • muffler
6 hp IH Mogul              parting out
  • was a complete running show piece
    a few years ago
  • I started to strip the old ugly paint
    but never finished
  • SOLD crank case
  • $250 crank shaft
  • $1,000 cylinder
  • $600 flywheel
  • SOLD piston
  • $100 rod
  • SOLD complete exhaust system
  • $350 sideshaft & governor
  • SOLD intake valve cage complete
  • SOLD exhuast vavle cage complete
    but repaired like most
  • Also, I have several of the smaller
    parts
Counter
2 1/2 hp Alpha Delaval       $525
  • will make a great winter project
  • loose
  • have not found any breaks, cracks,
    or welds
  • found the ignitor and original tin oiler
  • lots of original paint
  • crank guard
  • pulley
  • hit and miss governed
valve grinder       $100
  • in good condition
  • selling for a friend
  • said he has used it
  • I don't know anything about it
7 hp Hercules       parting out
  • was a complete running engine but
    am parting out and here is what is
    left
  • RARE low base Hercules
  • older restoration
  • one good flywheel left
  • very good compression before I sold
    the head off of it
  • ask for parts available
  • only bad thing I found was the
    bottom of water jacket had been
    busted out and jb welded back in
    and has fell back out but I have the
    piece
1 1/2 hp Empire     $850
  • hit miss engine
  • shouldn't take much to run
  • needs gas tank
  • skeleton base
  • muffler
  • oiler
  • pulley
Sieverkropp     $1,200
  • very nice
  • runs nice
  • twin vertical engine
  • one spark plug so both cylinders fire
    at same time
  • oilers on both cylinders
  • crank handle
3 1/2 hp Leader    $1,150
  • hit miss engine
  • early 3 digit serial #
  • disk crankshaft
  • has compression
  • shouldn't much to run
Railroad Velocipede     $5,000
  • very rare piece of history
  • in great shape
  • some original paint
  • Sheffeld
4 hp IHC Famous    $6,500
  • hit miss engine
  • runs nice ( see movie )
  • water pump and screen cooler
  • oiler
  • muffler
  • pulley
  • original skids
  • pipe axles and wheels so you can
    move
  • original battery box
  • has fuel pump
  • head has been repaired and drips
  • non pulley side flywheel has a little
    run out
3 hp Fuller Johnson DE  $4,500
  • running engine
  • DOUBLE EFFICIENCY
  • runs good (  watch video )
  • very unique design
  • igniter
  • fuel pump needs a spring on arm to
    hold against cam, spring is broken
  • oiler
  • hopper lid
  • older restoration
  • I have found no b/c/w's
live steam engine  $2,500
  • running engine
  • 7.5 guage
  • runs good (  watch video )
  • very unique design
  • ran on air for the video
Stickney cart    $850
  • 17" x 2 1/2" back wheels
  • 14" x 2 1/2" front wheels
  • 42" long rails
  • 10 7/8" outside of rails
6 hp Famous  $3,500
  • running engine
  • I have ran with a squirt bottle of gas
  • have a homemade gas tank that will
    need to plumbed back up but I have
    the pipes
  • great compression
  • original
  • throttle governed engine
  • oiler
  • crank guard
  • head has a repair on the bottom
  • timing gear has repair
  • muffler
2 1/2 hp Foos Junior   $3,500
  • good compression
  • has one electric lighting flywheel
  • runs good
  • hit miss governed
  • pulley
  • oiler
2 hp Detroit   $850
  • has compression
  • looks complete
  • shouldn't take much to run
  • no tag
  • correct two feed oiler
  • appears to have original skids and
    cooling tank and fuel tank
2 hp Jacobson   $5,500
  • good compression
  • haven't found any b/c/w's
  • I have ran this engine but haven't
    taken a video yet
  • pulley
  • crank guard
  • oiler
  • muffler
1 1/2 hp Olds   $2,500
  • haven't found any c/b/w's
  • pulley
  • crank guard
  • oiler
  • muffler
  • battery box
IHC large clutch pulley   $850
  • 26" diameter
  • 6 1/2" wide
  • 8 7/8" bolt pattern center to center
    on each spoke
  • took off a 8 hp Famous engine
  • should also fit 10 hp also
  • one clutch arm has been repaired
Alamo / Rock Island cart   $450
  • 15 1/2" x 3" rear wheels diameter
  • 14" x 3" front wheels diameter
  • 25" approx width overall
  • 47" rails long
  • 12 1/4" rails wide
McEwen Bros         $2,000
  • Looks complete
  • has compression
  • shouldn't take much to have running
    again
  • half breed
  • not sure on hp but guessing 12-15 hp
  • someone has added a screen tank
    and pump
  • flywheel 54"x 2 3/4" on one side
  • other flywheel is 60" x 3 1/2 "
1 3/4 hp Humphreys (hercules)sold
  • Looks pretty complete
  • hit miss governed
  • small flywheels
  • nice polished EK magneto
  • HOT mag
  • gas tank
  • oiler
  • show ready
  • no breaks, cracks, or welds
Eagle marine engine         $200
  • engine is loose but only partially
    moves
  • missing carb, timer
Victory Scooter LX10 with Hydraulic
Lift Kit - $4500
  • listing for a friend
  • This scooter and lift kit was
    purchased May 2018 for 6,500 - it was
    parked in the garage and never used.
    Manufactured in 2018, it has an
    electric hydraulic lift for easy
    transportation.
Below are specs.

The Victory® 10 LX with CTS Suspension
offers a smooth ride with performance to
match.

Comfort-Trac Suspension (CTS) is the next
generation in mobility scooter ride comfort.
Pride® Mobility's industry-first technology
incorporates advanced suspension
components for improved absorption over
rough surfaces and a more comfortable ride
experience over various terrains.

Comfort-Trac front and rear suspension
Feather-touch disassembly permits simple
frame separation with only one hand
Delta tiller with wraparound handles
Crush Proof Front Basket
Black, non-scuffing tires
Easy-to-read LED battery meter
Full LED lighting package that includes curb
and rear lights, directional signals and
courtesy light under the tiller
Auto-connecting front to rear harness
Easy Grip Tiller adjustment knob
Easy access tiller-mounted charger port
Storage compartment below tiller
Enhanced flush-mounted horn buttons
3 hp IHC M     $550
  • Looks pretty complete
  • EK magneto
  • oiler
  • haven't seen any breaks, cracks, or
    welds
1 3/4 hp United     SOLD
  • missing the ignition
  • missing the carb
  • oiler
  • haven't seen any breaks, cracks, or
    welds
2 hp NC Fuller Johnson     $500
  • looks complete
  • shouldn't take much to get running
  • oiler
  • EK mag
  • haven't seen any breaks, cracks, or
    welds
4 hp hp Cushman Binder     $350
  • shouldn't take much to get running
  • oiler
  • EK mag missing
  • haven't seen any breaks, cracks, or
    welds
2 hp Ottawa    SOLD
  • looks complete
  • shouldn't take much to get running
  • oiler
  • Webster mag that will need new
    springs
  • haven't seen any breaks, cracks, or
    welds
4 hp Cushman Cub     $350
  • looks complete
  • shouldn't take much to get running
  • EK mag
  • haven't seen any breaks, cracks, or
    welds
3-5 hp IHC lb     $350
  • looks complete
  • shouldn't take much to get running
  • mag
  • haven't seen any breaks, cracks, or
    welds
  • needs a gas tank
  • pulley
  • air cleaner
3 hp FW Economy     $450
  • shouldn't take much to get running
  • pulley
3 hp Brownwall     $900
  • looks complete
  • shouldn't take much to get running
  • haven't seen any breaks, cracks, or
    welds
3 hp Lister     $750
  • shouldn't take much to get running
  • piston skirt has been broken
  • should have a webster mag
2 hp Domestic     $2,350
  • Looks pretty complete
  • PR magneto
  • oilers
  • original muffler
  • flywheels look straight
  • haven't seen any breaks, cracks, or
    welds
  • has compression
  • shouldn't take much to have running
  • on original trucks except the front
    axle
  • will need a new diaphram for pump
    because current one has a hole
1 1/2 hp Cushman X     SOLD
  • Looks complete
  • model 21 type X
  • RARE
  • buzz coil in the battery box
  • oiler
  • haven't seen any breaks, cracks, or
    welds
  • on a wheel barrel cart